物理安全检测
AAMA 612 建筑用铝阳极氧化与透明有机复合涂层的推荐规范、性能要求和测试方法
AAMA 612 建筑用铝阳极氧化与透明有机复合涂层的推荐规范、性能要求和测试方法—测试标准
AAMA 612 Voluntary Specification, Performance Repuirements, and Test Procedures for Combined Coatings of Anodic Oxide and Transparent Organic Coating on Architectural Aluminum
AAMA 612 建筑用铝阳极氧化与透明有机复合涂层的推荐规范、性能要求和测试方法
AAMA 612 建筑用铝阳极氧化与透明有机复合涂层的推荐规范、性能要求和测试方法—测试范围
This specification describes test procedures and performance requirements for architectural quality combined coatings of anodic oxide and transparent organic coatings (hereafter referred to as the "combined coatings"), applied to aluminum extrusions and panels for architectural products. The primary units of measure in this document are metric. The values stated in SI units are to be regarded as the standard. The IP values given in parentheses are for reference only. This document was developed in an open and consensus process and is maintained by representative members of AAMA as advisory information.
本规范描述了用于建筑产品铝型材和面板的阳极氧化物和透明有机涂料的建筑质量复合涂料(以下简称“复合涂料”)的测试程序和性能要求。本文件中主要的度量单位是公制。以SI单位表示的值被视为标准。括号内的IP值仅供参考。该文件是在公开和协商一致的过程中制定的，并由美国医学协会的代表成员作为咨询信息加以维护。
AAMA 612 建筑用铝阳极氧化与透明有机复合涂层的推荐规范、性能要求和测试方法—检测项目及方法
AAMA 612 Section 7.1 ASTM B244复合涂层厚度 Combined coating thickness
AAMA 612 Section 7.2 ASTM B137氧化层重量和表观密度 Oxide coating weight and apparent density
AAMA 612 Section 7.3 AATCC 173色彩均匀性 Color uniformity
AAMA 612 Section 7.4 ASTM D523 60℃镜面光泽度 Gloss uniformity at 60℃
AAMA 612 Section 7.5 ASTM D3363有机涂层硬度 Organic coating hardness
AAMA 612 Section 7.6.1.1涂层干式附着力 Film dry adhesion
AAMA 612 Section 7.6.1.2涂层湿式附着力 Film wet adhesion(24h浸水,38°C)
AAMA 612 Section 7.6.1.3涂层沸水煮附着力 Film boiling water adhesion(20 mins, 99~100°C)
AAMA 612 Section 7.7耐冲击测试 Impact resistance
AAMA 612 Section 7.8 ASTM D968耐落沙磨耗 Abrasion resistance
AAMA 612 Section 7.9.1耐盐酸 Muriatic acid resistance
AAMA 612 Section 7.9.2耐泥浆 Mortar resistance
AAMA 612 Section 7.9.3 ASTM D2244 耐硝酸 Nitric acid resistance
AAMA 612 Section 7.9.4耐清洁剂 Detergent resistance
AAMA 612 Section 7.9.5耐窗户清洗剂 Window cleaner resistance
AAMA 612 Section 7.10.1 ASTM D2247 or ASTM D4585耐湿 Humidity resistance (4000h,100% RH,38°C)
AAMA 612 Section 7.10.2 ASTM B117 耐盐雾 Salt spray resiatance(4000h)
AAMA 612 Section 7.11裂纹测试 Craze resistant
AAMA 612 Section 7.12耐候测试 Weathering (南佛罗里达州,北纬27度,45度角面向南方,5年曝晒)
AAMA 612 Section 7.12.1.2 ASTM D2244 Section 6.3颜色保持力 Color retention
AAMA 612 Section 7.12.1.3 ASTM D4214耐粉化性 Chalk resistance
AAMA 612 Section 7.12.1.4 ASTM D523光泽度保持力 Gloss retention
AAMA 612 Section 7.12.1.5 ASTM B244耐侵蚀 Resistance to erosion
----------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------------
